|
1. |
Frequency range: |
|
Frequency
|
Step
|
Mode
|
|
0.5300 - 1.7000
MHz |
10 kHz |
AM |
|
25.0000 - 27.9950
MHz |
5 kHz |
AM |
|
28.0000 -
29.6950 MHz |
5 kHz |
FM |
|
30.0000 -
49.9950 MHz |
5 kHz |
FM |
|
50.0000 - 54.0000 MHz |
5 kHz |
FM |
59.7500,65.7500,71.7500,
81.7500,87.7500 MHz |
6000 kHz |
WFM |
|
88.000 - 107.9000 MHz |
100 kHz |
WFM |
|
108.0000 -
136.9875 MHz |
12.5 kHz |
AM |
|
137.0000 - 143.9950 MHz |
5 kHz |
FM |
|
144.0000 -
147.9950 MHz |
5 kHz |
FM |
|
148.0000 -
174.0000 MHz |
5 kHz |
FM |
179.75,185.7500,191.7500,
197.7500,203.7500,
209.7500, 215.7500 |
6000 kHz |
WFM |
|
225.0000 -
380.0000 MHz |
25 kHz |
AM |
|
406.0000 -
419.99375 Mhz |
6.25 kHz |
FM |
|
420.0000 - 449.99375 Mhz |
6.25 kHz |
FM |
|
450.000 - 469.99375 Mhz |
6.25 kHz |
FM |
|
470.0000 - 512.0000 Mhz |
6.25 kHz |
FM |
|
806.0000 - 823.9875 Mhz |
12.5 kHz |
FM |
|
849.0125 - 868.9875 Mhz |
12.5 kHz |
FM |
|
894.0125 - 956.0000 Mhz |
12.5 kHz |
FM |
|
2. |
Channel Memory Scanning — Scans
frequencies you have stored in any of the channels or banks at a rate of up to
70 channels per second. |
|
3. |
Memory Availability — Store and then scan any of up to 300 channels distributed
over 10 banks. |
|
4. |
SAME All-Hazards Operation — In standby mode, constantly monitors the last-tuned
station and alerts you if it detects an alert transmission for your area (NOAA
and broadcast channels only). |
|
5. |
Direct Channel Access — Press 0 - 9 and HOLD to directly access any stored
frequency. |
|
6. |
Channel Lockout/Frequency Lockout — Skip over stored frequencies (channels)
using the Lockout feature to enable faster scanning. Lets you designate up to
fifty frequencies to skip during a search (limit or service) to increase the
scanning speed. |
|
7. |
Radio Controlled Clock — Automatically sets to the precise time using NIST
broadcasts. |
|
8. |
AM/FM and TV 2-13 Broadcast — Lets you store up to 30 preset broadcast channels
(10 AM and 20 FM/TV) for quick access. |
|
9. |
Priority Channel — Designate a specific frequency as a Priority Channel. The
radio scans and checks that channel every 2 seconds. Select and designate up to
10 frequencies as Priority Channels (one per bank). |
|
10. |
Duplicate Channel Alert — Lets you know that a selected frequency has already
been programmed into memory if you attempt to store it again. |
|
11. |
Limit Frequency Searching — Lets you designate lower and upper frequency range
and search within that range for active frequencies. You can then store
frequencies in memory as channels for later recall. |
|
12. |
Service Search — Lets you designate one of the five preprogrammed service
channels (Police, Fire/EMS, Air, Ham, Marine) to search. |
|
13. |
• Scan Speed 70 channels per second maximum in SCAN MODE
• Search Speed 75 steps per second maximum in SEARCH MODE
• TURBO MODE For frequency steps 5kHz apart, searching occurs in Turbo Mode
which is 225 steps per second. |
|
14. |
Clock Display — The scanner always displays the current time. The clock also
features an alarm that lets you wake to the selected radio source or an alert
tone up to 20 minutes or be shut off manually. A convenient snooze button lets
you silence the alarm for an extra 5-minutes. |
|
15. |
Delay — You can enable or disable the 2-second delay to resume scanning when a
transmission ends. Enabling this feature helps prevent missing a response from
one of the parties in the transmission. |
|
16. |
LCD Backlight — You can enable or disable the LCD back lighted display. |
|
17. |
Contrast Adjust — Lets you adjust the LCD contrast for best viewing. |
|
18. |
Key Touch Tone — A tone sounds to confirm you have made a valid key input while
a different tone sounds to alert you to an invalid entry. |
|
19. |
EEPROM Memory Backup — The scanner uses a non-volatile EEPROM for memory backup. |
|
20. |
Battery Alert — A battery icon alerts you if no
battery is installed or the battery power is low. An alert tone sounds when the
battery needs to be replaced. The backup provides backup for the clock when
external power is off or not connected and will power scanning for a short time. |
|
21. |
Auto Power Off — Turns the scanner off when the battery power gets too low. |
